Shopping cart
MENU
My Account

Welcome to Big Boss Tactical

AEG TTM V2

Sort by:
Filter
Element AEG Silver Wiring Loom + High Capacity Switch $29.00

Quality Element Large Capacity Switch Assembly & Wiring Loom for AEG V2 Gearbox builds.

Please Note this is a pre-order item available for dispatch 29th July 2019

Sale
Fighting Bro FB Silver Wire Kit – Mini Tamiya Plug Ready $26.00

Quality Large Capacity Switch Assembly & Silver Wiring Kit for Jm9 and AEG V2 Gearbox builds.
– With Mini Tamiya Gel Ready Battery Plugs
– Fits Mini Tamiya Turnigy Batteries
– Includes Mag Contacts

JM M4A1 Gen9 / V2 AEG Trolley Switch Block $9.99

Works with V2 gearbox builds.

M4A1 Gen9 / AEG V2 Wiring Silver Wire Kit / Switch Block $25.00

Quality Large Capacity Switch Assembly & Silver Wiring Kit for Jm9 and AEG V2 Gearbox builds.
– With JST Gel Ready Battery Plugs

M4A1 Gen9 / AEG V2 Wiring Wire Kit + Switch Block $9.50

Wiring Kit for Jm9 and AEG V2 Gearbox builds.

M4A1 Gen9 / AEG V2 Wiring Wire Kit + Switch Block + More $29.99

Wiring Kit for Jm9 and AEG V2 Gearbox builds.

Description:
– JST Gel Ready Battery Plugs
– Motor connector clips/connectors ready
– Switch Block + Block Return Spring
– Mode Selector Plate
– Safety Latch + Spring
– Trigger Spring
– Other Screws & Springs

Perun V2 Optical Mosfet ( Comes Wired With Deans Plug ) $145.00

Perun V2 Optical is a device that replaces mechanical contacts in version 2 gearboxes with an electronic circuit based on MOSFET transistors and adds a multitude of new functions to your replica.

Elimination of mechanical contacts solves the problem of their gradual wear. MOSFET transistors utilized in Perun V2 have a much lower resistance than contacts, which also increases rate of fire. Small elements in the trigger mechanism responsible for semi-automatic fire frequently malfunction, especially in replicas built on parts made by many different manufacturers. Perun V2 minimizes the number of moving parts in your replica, increasing reliability and ensuring proper functioning of all firing modes. Perun V2 itself has no moving parts at all thanks to use of optical sensors for gear, trigger and selector plate detection.

Features

Use of a microcontroller enhances capabilities of your airsoft gun by providing possibility to set any combination of the following firing modes under “SEMI” and “AUTO” selector positions independently:
– safe
– semi-automatic
– 2 to 5 round burst
– full-automatic
Programming of all of the settings, not only firing modes but also switching active brake, precocking and battery protection on and off is done solely by using easily memorable sequences of fire selector switching and trigger pulls. That allows changing the settings at any moment in a matter of seconds, even under enemy fire.

One of the most important features of Perun V2 Optical is precocking. Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, piston will remain in rear position after each shot with spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. Microcontroller uses data from optical sensor to calculate current sector gear position and speed. With this information, after releasing the trigger, smart algorithms are able to transfer only enough power to the motor to make the piston stop in the correct position, or in high ROF setups, to let the motor inertia push the piston back and stop it using active breaking right. This saves your battery and reduces motor wear. Precocking works in semi, burst and full-automatic modes.

Perun V2 Optical has an active brake allowing to stop the motor after each shot. In case of double shot problem in replicas with high rate of fire, active brake will be an effective solution if you do not want to use precocking. It can also prevent compression of the main spring for a longer time, if you will fire a shot with AB on before a storing your replica for a longer time. Active brake can be switched on or off at any time in few seconds.

Battery protection mode is dedicated to Li-Po batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every 30 seconds. This may also be freely switched on and off.

Double shot mode allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pressed, but also when it’s released.

The integral part of Perun V2 Optical is a ready for installation low-resistance wiring based on Muldental silicone wires, which are praised by airsoft techs and widely considered best for airsoft electric guns. Perun V2 Optical is available both front and back wired.

Thanks to use of exceptionally efficient and powerful MOSFETs, the device can be used in replicas with any main spring. The maximum rate of fire is 50 RPS.

Compatibility

Perun V2 was tested with positive outcome in gearboxes of the following manufacturers: G&P, G&G, Classic Army, KWA, Ultimate, A&K, PJ, JG and Specna Arms. Gearboxes made by  ICS, E&L, Cyma and Krytac may need sanding down of some elements. That refers to gearboxes in Tokyo Marui standard, Perun V2 will not work with non-Tokyo Marui standard gearboxes like for example ARES EFCS. Perun V2 fits to elongated V2 gearboxes used in SR25 replicas.

Perun V2 works well with DSG and short stroked setups, because optical sensors are not subject to mechanical stress seen in those high ROF configurations and algorithm for cycle detection is very elastic. Our tests have shown that in some DSG setups precocking may be less reliable and has to be disabled. However, ROF provided by DSG makes use of precocking rather unnecessary.

T238 JM9 / JM GEN9 GEN10 / V2 Ver.2 Optical MOSFET / Digital Trigger – Rear Wired $95.00
  • Programmable digital trigger
  • New and improved Optical Detection Version 1.5
  • Rear Wired (Silver Wiring)
  • Programs include:
    – Piston return to un-tensioned postion mode for gearbox stress reduction
    – Single Stroke, Double Stroke, and Multiple Bursts Fire Modes (1-9 Shots)
    – Low voltage battery protection and gearbox stall protection
  • Supports up to 240A starting current and 100A braking current
  • Suitable on JM9 / JM10 / V2 Gearboxes
  • Mosfet is 95% soldered. (Mag contacts soldering is required).
    Specifications:– Product Weight: 90g
    – Package Dimensions: 16 x 16 x 4cm
    – Package Weight: 100g
    – Box / Foam Packaging
T238 JM9 / V2 Ver.2 Optical MOSFET / Digital Trigger $59.95 – $75.00

– Equipped with a high-speed micro digital processor and two high-power FET chips
– Has Active Braking Function which returns piston to de-compressed position
– Programmable multi-shot modes: 1 / 2 / 3 shot functions
– Battery Low Voltage Protection
– Improved trigger response sensitivity
– Can be used with battery as high as 14.8v
– Fit JM9 / V2 all V2 platforms such as Well M4, Kublai, SLR, LDT, & Fighting Bro
– Size: 45*30*10mm
– Working Voltage: 7.5v-14.8v
– Supports up to 240A starting current and 100A braking current
– Product Dimensions: 4.5 x 3 x 1cm
– Product Weight: 13g

Additional Information:
– Do not use a spring higher than M140
– Use batteries with high discharge rate

Also available in rear wired option. Choose from Options

V2 / V3 Gearbox Easy Wiring Micro SMD MOSFET $29.99
The Micro SMD Mosfet unit is a very affordable way to achieve higher performance from your blaster.
Achieve a higher rate of fire, and faster trigger response.

The Micro SMD Mosfet unit acts as a replacement for the mechanical trigger switch assembly, turning it into just a signal provider.
Due to a much lower electrical resistance in the Mosfet, the result is a faster trigger response, higher Rate of Fire and elimination of switch burnouts.
Using the latest SMD technology the Mosfet unit is extremely small (9.2 x 17.3 x 4.0 mm) which makes it possible to use in almost any blaster.
Includes a user manual.
Advantages:
*Faster trigger response
*Higher Rate of Fire
*Eliminates mechanical switch burnout
*Much lower electrical resistance
*Extremely small dimensions due to SMD technology
Current: 10A Constant; 18A Max
Compatibility: Version 2 and version 3 AEG (any switch assembly with a sliding trolley contact)
Compatible with all battery voltage from 7.4v – 11.1v Lipo/Li-ion and 4.8v – 14.4v Nimh battery. 

Showing all 10 results

error: Content is protected !!